I recently completed installation of new pistons in my 1953 Square 4 MK II.
With guidance from noted Ariel expert Paul Ackerman, I used a completely different procedure than the daunting process suggested in the Ariel factory workshop manual, and found the task to complete without issue.
I have documented the process, with pictures. You can view the document here:
http://blog.auldridge.org/wp-content/up ... UARE-4.pdf
Installing Pistons in a Square 4
-
- Posts: 43
- Joined: Sun Mar 04, 2018 9:59 pm
- Location: Austin
- Contact:
Installing Pistons in a Square 4
Phil Auldridge - Austin, Texas
1953 Ariel Square 4
1997 Honda Valkyrie
1972 Norton Combat Commando
1978 BMW R100/7
1980 Honda CBX
2014 Indian Chief
1975 Moto Guzzi 850T
1953 Ariel Square 4
1997 Honda Valkyrie
1972 Norton Combat Commando
1978 BMW R100/7
1980 Honda CBX
2014 Indian Chief
1975 Moto Guzzi 850T
-
- Posts: 1
- Joined: Tue Mar 06, 2018 7:34 pm
- Contact:
Re: Installing Pistons in a Square 4
The method described by Phil works, but can be hard work. My normal approach, with the engine in the frame, is to use two bungees wrapped over the top frame tube to support the cylinder. Using piston ring clamps, I then put the pistons in the cylinders one at a time - which you can do easily enough with the weight of the cylinder taken by the bungees, provided that you get the bungees to the right tension.
I have recently had to build two MkII engines without the benefit of a frame tube to use for the bungees. So I went back to the textbook approach of supporting the pistons underneath and resting the cylinder on the ring clamps. You cannot do this without ring clamps, in my opinion. The thickness of the steel / timber strips under the pistons was a problem because in each engine I was using BMC pistons instead of Ariel ones and the skirt length is different. I concluded that the thickness of the support strips is not critical, provided that they hold the pistons square to the bores. What does seem to vary is the position of the cylinder above the crankcase as it may be forward or backward from the correct position, depending on the thickness of supports used. But once the pistons are in the cylinder, you can adjust location easily enough.
Fundamentally, you get the pistons square to the bores at about the correct positions. Then you place the cylinder on top such that the cylinder skirts are all bearing down equally on the piston ring clamps. Then you simply tap the cylinder down gently until all the rings are in the cylinders. Make sure they are far enough in, remove the piston ring clamps and then adjust the cylinder location to suit the cylinder base studs. In practice, this is an awful lot easier than it sounds.
Paul
I have recently had to build two MkII engines without the benefit of a frame tube to use for the bungees. So I went back to the textbook approach of supporting the pistons underneath and resting the cylinder on the ring clamps. You cannot do this without ring clamps, in my opinion. The thickness of the steel / timber strips under the pistons was a problem because in each engine I was using BMC pistons instead of Ariel ones and the skirt length is different. I concluded that the thickness of the support strips is not critical, provided that they hold the pistons square to the bores. What does seem to vary is the position of the cylinder above the crankcase as it may be forward or backward from the correct position, depending on the thickness of supports used. But once the pistons are in the cylinder, you can adjust location easily enough.
Fundamentally, you get the pistons square to the bores at about the correct positions. Then you place the cylinder on top such that the cylinder skirts are all bearing down equally on the piston ring clamps. Then you simply tap the cylinder down gently until all the rings are in the cylinders. Make sure they are far enough in, remove the piston ring clamps and then adjust the cylinder location to suit the cylinder base studs. In practice, this is an awful lot easier than it sounds.
Paul
Paul Jameson
Former AOMCC Singles Spares Organiser, General Secretary and Machine Registrar and Archivist over a 25 year period.
1936 4G (pushrod) 1000c Square Four
1937 RH500
1952 ex ISDT KHA 500 (Project)
1954 KH(A)
1975? Healey 1000/4 (Project)
Former AOMCC Singles Spares Organiser, General Secretary and Machine Registrar and Archivist over a 25 year period.
1936 4G (pushrod) 1000c Square Four
1937 RH500
1952 ex ISDT KHA 500 (Project)
1954 KH(A)
1975? Healey 1000/4 (Project)
Who is online
Users browsing this forum: No registered users and 3 guests